Modules

On this forum you can discuss iRidium modules with other users. Please post here your questions, ideas or errors you find.

+1
Under review
Wouter Verbeeck 4 months ago in Domintell / Domintell Scanner • updated by Wouter Verbeeck 3 months ago 28

Today we tested scanning a Domintell infrastructure. Iphone 7; andriod on Huawai P9


Findings:

After scanning, we can find the serial numbers of the modules in the listing. Once selected eand imported, this serial number cannot be seen in the module overview nor in the module detail (i.e domintell relay).

Also, in the module detail, we cannot see the given names of each relay contact, name from Domintell on iPhone7, but we CAN on android (was ok in previous version of i3 lite).


Once assigned a few relay contacts (2 relmay modules, 2 contacts from each module) to a room, we found the following:

- We receive feedback from Domintell when the staatus of a relay is changedby a physical

button.

- We can not send command to Domintell relay module.


Please advice


regards,

Wouter

0
Under review
Theo Derks - NL (distributor) 5 months ago in Domintell / Domintell Scanner • updated by Ilya Markov (expert) 5 months ago 11

Hi,

when using the Domintell scanner with a DETH02 interface with a PASSWORD set OR a different portnumber set, the module is crashing.


Please add the possibility, to use a password on the DETH02 and add the possibility, to use passwords on the DETH02 interface.


Thanks


Theo


0
Completed
Ilya Markov (expert) 7 months ago in Domintell / Domintell Sound Module • updated 7 months ago 1

Domintell Sound Module

The module enables control of Sound module in the Domintell bus. Enter the parameters to control the device:

Host, Port, Password (if set) of the bus, serial number of the device.
Supported modules: DAMPLI01.
Functions:
- Source control;
- Volume control;
- FM tuner.
A set of Actions, Event and Conditions allows you to use all module functions in macros and routines:
Actions:
1) Source - to select the source;
2) Volume - to set the volume;
3) Tuner (FM) - to tune the radio.
Events:
1) Source - the source has changed to the indicated value;
2) Volume higher - the volume has become higher than the indicated value;
3) Volume lower - the volume has become lower than the indicated value.
Conditions:
1) Source - the source is set up to the indicated value;
2) Volume higher - the volume is higher than the indicated value;
3) Volume lower - the volume is lower than the indicated value.
0
Completed
Ilya Markov (expert) 7 months ago in Domintell / Domintell Shutter • updated by Wouter Verbeeck 3 months ago 2

Domintell Shutter

The module enables control of Shutter devices in the Domintell bus. Enter the parameters to control the device:

Host, Port, Password (if set) of the bus, serial number of the device, also choose name of your module.
Supported modules: DTRV01, DTRP02, DTRVBT01.
Functions:
- Open;
- Close;
- Stop.
A set of Actions, Event and Conditions allows you to use all module functions in macros and routines:
Actions:
1) Down - to close the blinds;
2) Open - to open the blinds;
3) Stop - to stop the blinds.
Events:
1) Open - the shutter had just been opened;
2) Close - the shutter had just been closed.
Conditions:
1) Open - the shutter is opened;
2) Close - the shutter is closed.

0
Completed
Ilya Markov (expert) 7 months ago in Domintell / Domintell Scanner • updated by Slava Zhuravlev (expert) 1 month ago 3

Domintell Scanner

The scanner finds Domintell devices. To search the devices enter parameters of the Domintell bus: Host, Port and Password (if set). After the search process you can select the devices you need and add modules for them just with a click of the button. You can see available Domintell modules in iRidium store.
Available Domintell modules:
- Button (DPBR02, DPBR04, etc.);
- Dimmer (DDIM01, DOUT10V01);
- Fan (DFAN01);
- Relay (DBIR01, DMR01, etc.);
- Shutter (DTRV01, DTRP02, DTRVBT01);
- Sound module (DAMPLI01);
- Temperature (DLCD03, DTEM01, etc.).
0
Completed
Ilya Markov (expert) 7 months ago in Domintell / Domintell Relay • updated by Wouter Verbeeck 3 months ago 2

Domintell Relay

The module enables control of relay devices in the Domintell bus. Enter the parameters to control the device:

Host, Port, Password (if set) of the bus, serial number of the device, also choose name of your module.
Supported modules: DBIR01,DMR01,DTRP01,DLEC01.
Functions:
- On / Off.
Actions:
1) On – to turn on the switch;
2) Off - to turn off the switch.
Events:
1) On – the switch had just been turned on;
2) Off - the switch had just been turned off.
Conditions:
1) On – the switch is on;
2) Off – the switch is off.
0
Completed
Ilya Markov (expert) 7 months ago in Domintell / Domintell Movement Detector • updated 7 months ago 1

Domintell Movement Detector

The module enables control of Inpute devices in the Domintell bus. Enter the parameters to control the device:

Host, Port, Password (if set) of the bus, serial number of the device.
Supported modules: DMOV01.
Functions:
- Display input state.

The "On" and "Off" Events and Conditions can be used in macros and scenes (routines).

0
Completed
Ilya Markov (expert) 7 months ago in Domintell / Domintell Input • updated 7 months ago 1

Domintell Input

The module enables control of Inpute devices in the Domintell bus. Enter the parameters to control the device:

Host, Port, Password (if set) of the bus, serial number of the device, also choose name of your module.
Supported modules: DIN10V01, DISM04, DISM08, DISM20.
Functions:
- Display input value.
A set of Events and Conditions allows you to use all module functions in macros and routines:
Events:
1) Value - value has become equal to the indicated value;
2) Value higher - value has become higher than the indicated value;
3) Value lower - value has become lower than the indicated value.
Conditions:
1) Value - value is equal to the indicated value;
2) Value higher - value is higher than the indicated value;
3) Value lower - value is become lower than the indicated value.
0
Completed
Ilya Markov (expert) 7 months ago in Domintell / Domintell Fan • updated 7 months ago 1

Domintell Fan


The module enables control of buttons in the Domintell bus. Enter the parameters to control the device:

Host, Port, Password (if set) of the bus and serial number of the device.
Supported modules: DFAN01.
Functions:
- Fan speed control;
- Fan mode control.
A set of Actions, Event and Conditions allows you to use all module functions in macros and routines:
Actions:
1) Speed - to change the fan speed;
2) Mode - to change the fan mode.
Events:
1) Speed - the fan speed had just been changed;
2) Mode - the fan mode had just been changed.
Conditions:
1) Speed - the fan speed is set up to the selected value;
2) Mode - the fan mode is set up to the selected value.
0
Completed
Ilya Markov (expert) 7 months ago in Domintell / Domintell Dimmer • updated 7 months ago 1

Domintell Dimmer

The module enables control of dimmers in the Domintell bus. Enter the parameters to control the device:

Host, Port, Password (if set) of the bus, serial number of the device, also choose name of your module.
Supported modules: DDIM01, DOUT10v01.
Functions:
- Power control;
- Brightness control.
A set of Actions, Events and Conditions allows you to use all module functions in macros and routines:
Actions:
1) On – to turn on the light;
2) Off - to turn off the light;
3) Value - to set brightness (or some other parameter) of the light.
Events:
1) On – the dimmer had just been turned on;
2) Off - the dimmer had just been turned off;
3) Value higher - brightness has become higher than the indicated value;
4) Value lower - brightness has become lower than the indicated value.
Conditions:
1) On – the dimmer is on;
2) Off – the dimmer is off;
3) Value higher - brightness is higher than the indicated value;
4) Value lower - brightness is lower than the indicated value.