KNX Home Server and i3 KNX. Changelog (EN)

RU: История версий KNX Home Server на русском языке

KNX Home Server v1.9.0 and i3 KNX app v1.9.0

Released: 31.03.2021


Changelog (main changes):

- Guest access mode is added – access to certain rooms can be limited, remote control and setting timers can be allowed or banned; link
- Support of Fanvil intercom is added; link
- The text of the info message about no connection to the KNX bus is changed; link
- Conversion of images during uploading to a project is added; link
- The “Shutters” device is updated; link
- Deathorization from panels during password change is added; link
- The display of the target temperature during the movement of a sliding bar is added (earlier it was displayed only when a sliding bar is released); 
- Switching off the screensaver by activation of a motion sensor is added for Android; link
- The range of values for ""Digital display"" device in increased up to eight-bit negative numbers and fractions;
- Import of ETS projects with a password is added; link
- TP1 physical address is divided with dots (used to be with a slash)
- Auto start of the app after installation on Windows is added.
- Dutch localization is updated
- Error is corrected: freezing of server update
- Minor improvements and corrections


KNX Home Server v1.8.0 and i3 KNX app v1.8.0

Released: 11.03.2021

Changelog (main changes):

- A system of backups is added: a capability to cancel changed on the server and in the i3 KNX app
- An error in the app work on DIVUS panels is: a navigation panel is always displayed
- KNX module, Climate: a capability to set “Thermostat modes” block of buttons is added
- KNX module, Climate: a capability to set a step of changing the required temperature (changing by 0.5 or 1 degree) is added in the widget and in routines.
- KNX module, Dimmer: a capability to set a step of absolute dimming is added
- KNX module, Dimmer: touch area of slider of a circular dimmer is increased (for more convenient control of brightness with the help of a circular dimmer)
- KNX module, Shutters: an error in the work of "Open" and "Close" routines (the routine did not work if a long press was not set)
- KNX module, Input number, Digital display: the heading area is increased (the heading of a widget can contain more symbols)
- SIP module: the "open/close door", "turn on/off light" events are added to intercoms
- The "Make public" button is now called "Save on server " and it is located in the top part of the app
- When the password of an account is changed, it is possible to reset authorization and remote access of devices authorized with this account.
- Control of edge lighting of iRidium panel P7-PoE from macros, modes and routines is added.
- Server update to the latest version when activated from the config is added (after resetting).
- Screensaver mode is added for built-in panels (iRidium panel 7, etc.). It is available only for templates.
- An error is corrected: the name of Wi-Fi network could not be identified on some devices when a project was created
- Errors are corrected, translation is improved and added

KNX Home Server v1.7.0 and i3 KNX app v1.7.0

Released: 27.01.2021

Changelog (main changes):

- Demo-mode for end-users is realized
- Fast access to setting timers is added
- i3 KNX version for Android with kiosk-mode support is added.
- Events of call start and call end of SIP server to use in routines are added.
- Sending IP address via a cloud for reliable location in the network is realized.
- Sonos driver is updated
- Minor corrections and developments

KNX Home Server v1.6.1 and i3 KNX app v1.6.1

Released: 26.11.2020

Changelog (main changes):

- The climate widget for KNX can work with 1 bit shift

- An error is corrected: timers can be activated by events of an astronomical timer (sunrise, noon, ...)

- It's easier to move floors in the mobile version

- Dutch and French localization is updated

- An error is corrected: devices located only on the main page can be used in macros and routines

KNX Home Server v1.6.0 and i3 KNX app v1.6.0

Released: 06.11.2020

Changelog (main changes):

- Google Home voice assistant is added
- Capability to add any widget to the main page is added, more layout capabilities are added
- Sonos: Favorites playlists can be added to the list to play
- A new module, "Web page" is added (following a link in the app)
- Other improvement and corrections

Changelog (detailed):

- Improvement: Google Home voice assistant is added
- Improvement: In Sonos Favorites playlists can be added to the list to play
- Improvement: In Sonos search of speakers in the local network for fast adding to a project is available (no need to enter the IP-address of the speaker manually)
- Improvement: Capability to drag floors in the Floors and rooms list is added
- Improvement: Capability to set a definite brightness value of a dimmer in timers is added
- Improvement: Selection of a way to connect i3 KNX to the server is moved to the step of project creation, the 4th step of the start setup is substituted
- Improvement: Button KNX Device can now process a "short" and "long" press separately (there used to be only a short press)
- Improvement: Any widgets, and not only modes and macros, can be added to the main page of the app.
- Improvement: "Large photo", like on the main page, can be added to any room, the photo on the main page canbe deleted of replaced with a small one.
- Improvement: The location of a room list on smart phones can be changed by moving “Rooms on phone” block on the main page of the app.
- Improvement: На Android устройствах теперь можно настроить значение DPI can be set on Android devices if the ratio of sides makes the interface look distorted or does not allow all widgets to be displayed on a screen fully. DPI setting is available on the main screen of the app (in project list), in user settings – top left corner
- Improvement: An end-user can link i3 KNX project in Yandex Alice if he is given such a “right”.
- Improvement: A project can’t be made public if KNX Home Server has a later version and i3 KNX has an earlier version (client update is required)
- Improvement: KNX dimmer always displays brightness value in per cent, %
- Improvement: Highlight of used group addressed of KNX devices in the list of imported group addresses is added
- Improvement: New Web page module is added)
- Development: A user without administration rights sees only information about himself in the Config (full list of users is hidden)
- Development: Capability to skip the step of client update at the app start is added
- Development: Increase/decrease icons on the widget of KNX dimmer are replaced with neutral - and +
- Error correction: Search of group addresses does not depend in the register in Cyrillic
- Error correction: Faster app start with Traditional Chinese localization
- Error correction: Wrong RGB commands were sent from Alice to KNX
- Error correction: In i3 KNX on Windows after changing network connection search of server stopped working forcing to restart the app.
- Error correction: Symbols with subscript signs in page heading are no longer cut
- Error correction: A white stripe on the main screen of the app when it is launched on iRidium panel 7 is deleted
- Error correction: Sonos S2 search did not work
- Error correction: (Х) button to exit the app disappeared during navigation in the Welcome pages on the full screen mode
- Error correction: A hyperlink was not seen in the highlighted line of a table of group addresses in the dark theme (Import table)
- Error correction: When a user was invited to a project a second time, a letter did not come to an e-mail
- Error correction: Creating a single mode was not considered as changes in a project, requiring publication


    KNX Home Server v1.5.0 and i3 KNX app v1.5.0

    Released: 25.09.2020

    Changelog:

    - Yandex Alice voice assistant
    - Control of Sonos
    - Saving group addresses from ETS project between sessions
    - Display of group addressed from ETS project on mobile devices
    - Import of building structure (floors and rooms) from ETS project
    - French localization is added, Chinese localization is updated
    - New parameter to control dimmer: dimming speed
    - Widgets of a dimmer and a media remote are improved
    - A device to send time and date to addresses of KNX bus is added

    KNX Home Server v1.4.1 и i3 KNX app v1.4.1

    Released: 01.09.2020

    Changelog:

    - Amazon Alexa voice assistant is added

    KNX Home Server v1.4.0 и i3 KNX app v1.4.0

    Released: 19.08.2020

    Changelog:

    - KNX widgets are improved
    - Errors are corrected

    KNX Home Server v1.3.0 и i3 KNX app v1.3.0

    Released: 24.07.2020

    Changelog:

    - full-size remote for Samsung TV is corrected (problems with display)
    - volume buttons on KNX media remote are corrected
    - TP1 interface is selected as a way to connect to KNX by default in a new project

    KNX Home Server v1.0.0 и i3 KNX app v1.0.0

    Released: 15.07.2020

    Changelog:

    - control of KNX with the help of ready widgets
    - import of group addressed from ETS (only on Windows)
    - secure remote control from iOS, Android, Windows
    - creation of timers, scenes, schedules
    - IP-cameras
    - SIP intercom
    - Samsung TV (Q series 2019)
    - white and black interface styles
    - 7 languages of the app

    Is this article helpful for you?